This RitFit M2 3D Smith Pro review follows Luke of Luke's Garage Gym through three months of use, and his verdict is that the rack is a mid-tier system built to last. He walks through the 13-gauge frame, the aluminum pulley trolleys, the 3D Smith carriage, the 154-pound stacks, and the attachments that come with the system.
This summary keeps his praise and his complaints side by side, so you can judge whether the 3D carriage and the extra stack weight are worth the jump from the M1 2.0.
Quick Answer: Luke says the RitFit M2 3D Smith Pro is a versatile mid-tier all-in-one rack that should last a lifetime, and he found the 3D Smith carriage noticeably harder than a standard Smith machine. He recommends it for buyers who want horizontal bar travel and a 154-pound stack per side, and he flags hook spacing, cable length, and one trolley bracket as the fixes he would want.
Key Takeaways
- Mid-Tier Build: Luke says the M2 moves RitFit above its budget tier, with 13-gauge front uprights instead of the 14-gauge steel on the M1 2.0.
- 3D Carriage: The 3D Smith glides horizontally as well as vertically, and Luke found squats and benches much harder on it than on a standard Smith machine.
- Stack and Loading: Each side carries a 154-pound stack on a 2-to-1 ratio, and the weight horns take two bumper 45s or about three thinner 45s.
- Smooth Pulls: Luke calls the aluminum pulleys smooth and consistent, and he says the guide rods need silicone spray before the first session.
- Feedback, Not Dealbreakers: Luke wants tighter Smith hook spacing, a shorter or adjustable lat pulldown cable, and a removable trolley bracket, and he says Matt at RitFit has already listened on the hook spacing.
Is the RitFit M2 3D Smith Pro a Good Home Gym Rack?
Luke calls the RitFit M2 3D Smith Pro a mid-tier rack that should last the rest of your life. He bases that call on range rather than a single headline feature, because the machine combines a half rack, a functional trainer, a Smith machine, a 3D Smith carriage, and storage in one footprint.
- Half rack: Front uprights remain open for benching, squatting, or rows, although Luke says he never uses them for those lifts.
- 3D Smith: The carriage travels vertically and horizontally to mimic a barbell path.
- Stacks: Two weight stacks rated to 154 pounds per side, with weight horns for extra plates.
- Storage: A rear beam for attachments and space for up to three barbells.
- Cable work: Aluminum pulleys with swiveling trolleys and a full set of attachment points.
Luke also places the M2 series above RitFit's budget tier, and he credits the add-ons, the 13-gauge steel, and the 3D carriage for the move upmarket. That positioning frames every comparison he makes later in the video.
What Steel and Uprights Does the M2 Use?
Luke says the M2's front uprights use 13-gauge steel, up from the 14-gauge steel on the M1 2.0. He describes 13 gauge as closer to the 12-gauge steel used in light commercial racks, while 14 gauge remains fine for home use and 11 or 10 gauge sits at the commercial level.
The uprights are otherwise the same as the M1, apart from the black or red finish. Luke points to the 1-inch holes spaced about 2 inches apart and the 2.3-by-2.3 upright size as the details that decide which attachments fit.
- Hole pattern: 1-inch holes with roughly 2-inch spacing, the same as the M1.
- Upright size: 2.3 by 2.3 inches, which sits between the common 2-by-2 and 3-by-3 standards.
- Finish: Black or red, with half-circle cutouts through the design.
- Luke's suggestion: Offer 11-gauge uprights or a 3-by-3, 12-gauge option with 1-inch holes for buyers who want a more standard platform.
Luke acknowledges that the in-between size limits some third-party attachments, which matters to buyers who like upgrading across brands. He counters that 1-inch holes accept attachments designed around that pin size, so the rack is not closed off entirely.
How Do the Trolley and Aluminum Pulleys Perform?
Luke says the trolley swivels with his body and the aluminum pulleys keep tension consistent through the full range. He counts 16 numbered adjustments on each trolley, with a pop pin that screws in and tightens instead of a quick-release lever.
The pulley housing rotates toward the middle or the side, which lets the cable follow the angle of the movement. Luke prefers that behavior to a fixed pulley because it feels more natural and avoids the stuck points he associates with simpler cable systems.
He also singles out the black carabiners and the Allen key cable ends as his favorite style. He explains that rubber cable balls can slide into the cable system after monthly silicone maintenance and jam the movement, so the Allen key attachment avoids a failure he has seen on other machines.
That detail is small, but Luke treats it as a sign that RitFit pays attention to parts that fail in daily use. He gives the brand credit for choosing the cable end he prefers rather than the cheaper option.
What Makes the 3D Smith Different From a Standard Smith?
Luke says the 3D Smith adds horizontal travel to the vertical bar path, and he found that motion much harder than he expected. The standard Smith section gives him vertical travel, 10 weight pegs for the hooks, and spotter arms for support at different heights.
He calls the peg-and-hook system the safest option compared with brands that use small holes for the bar to snap into, based on his own bad experiences. The 3D version adds horizontal glide, which he demonstrates with the spotters in the second position for bench, squat, and row patterns.
Luke says the motion suits lifters who lack stabilizing strength in the quads, shoulders, or chest, or who want a bar path closer to a free barbell. He is explicit that he is a middle school teacher who likes training at home, not a coach or personal trainer.
He also says the 3D Smith is much harder than he imagined, largely because multiple knee injuries and years of neglected leg training left him with weak stabilizers. He treats that difficulty as useful rehab work that mimics a barbell squat, and he notes that the carriage can be pinned for vertical-only Smith movements when he wants them.
For benching, Luke sets the Smith carriage toward the rear so it can travel horizontally as well as vertically. He says a buyer should want both directions at once, otherwise the 3D feature is not worth paying for.
"A Smith machine like that mimics more of a bar path, which could add a lot of benefit to people out there in the home gym space."
Luke, Reviewer, Luke's Garage Gym, RitFit's M2 3D Smith Machine Review
How Much Weight Do the Stacks and Weight Horns Hold?
Luke says each stack tops out at 154 pounds on a 2-to-1 ratio, so the effective load is roughly half of the plates and stack combined. He reads the stack in pounds and kilograms, with a 22-pound starting weight, and reminds buyers to account for the carriage and top weight.
- Bumper plates: Two 45s fit on a horn, and a third will not stay on.
- Thin plates: Handle plates and other thin 45s may allow about three per side.
- Mixed loading: Two 45s plus a 25 adds elevation without needing a third 45.
- Practical ceiling: Luke says three 45s per side plus the full stack is plenty for pulley work.
He recommends thinner plates if you want more load on the horns, because bumper plates consume the available space quickly. The horns also come off, which he shows as an option for lifters who want them elsewhere on the rack.
Which Attachments Come With the M2 3D Pro?
Luke says the package covers the main training stations, and his favorite attachment is the aluminum D handle. He separates what comes with the rack from the lat pulldown piece, which he says RitFit sells as a separate add-on.
- D handles: Aluminum, about $20 to $22 on RitFit's site in Luke's description, or under $20 with his link and code; that attachment price was not re-verified for this article as of November 18, 2026. The grip is passive but present, and he prefers it to rubber handles.
- Spotter arms: 1-inch holes on both sides, a pad, and a pin that fits the upright holes.
- J cups: A newer design with 1-inch holes that fits the 2.3-by-2.3 uprights.
- Dip bars: The same as the M1, with smooth black powder coat and no knurling; Luke asks for at least passive knurling for heavier dips and dip belts.
- Storage: A rear beam holds J cups, spotter arms, and dip attachments, and the back also holds three barbells.
- Landmine and curl bar: The landmine has a tightening knob, and the curl bar rotates with the wrist instead of locking into one position.
- Lat pulldown: Sold separately, with a seat that has four pad adjustments; Luke uses the second setting at 6 feet tall.
- Row station: A foot support and pin, with room for two 45s per side plus the stack.
Luke's lat pulldown setup puts the trolley and seat at their lowest positions, because the seat would hit the pulley wheel if it went lower. He still gets a full stretch at 6 feet and 210 pounds, but he warns that taller lifters may run out of cable.
The front of the rack also has band pegs on both sides for banded squats or benches, and the Smith can be pinned back to vertical travel when bands are not in use. Luke counts that flexibility as part of the system's value rather than a list of extras.
How Did the M2 3D Pro Hold Up in Luke's Testing?
Luke says the pulley system stayed smooth under a full stack plus plates, and he trained on the machine about once a week for three months. His first test is a lat pulldown with the lat piece, starting at the full 154-pound stack plus the top weight peg and adding plates from there.
He starts with a 45 per side, then adds thin 25s, then thin 10s and bumper 10s, and says the final load is close to what he actually uses. At 45s and 25s he estimates 12 hard reps before he is gassed, and he notes that his best lat pulldown in college was about 280 pounds.
One setup issue shows up before the plates go on: the stack shakes and adds tension until the guide rods are sprayed. Luke says to lubricate the rods before the first session, and the shake goes away once the rods are slick.
For hip thrusts, he stands on a 35-pound plate to raise his feet at 6 feet tall, sets the trolley at its lowest point, and lines up the bench before locking in. He says the setup lets him skip a deep range that bothers his back while still loading his glutes.
His bench test is an incline press with 35s and no clips at that weight, though he notes RitFit sells clips for heavier sets. He describes the linear bearings as smooth rather than harsh, and he says the bar path feels more difficult than a standard Smith because it moves in two directions.
The RDL and hip thrust workaround is a stack of plates under his feet, which he calls the simplest fix for machines that do not go low enough. Standing on plates gets him about halfway between his shins for an RDL, and a 25 per side takes him lower if he wants more stretch.
What Are the M2 3D Pro's Specs and Weight Ratings?
Luke lists an 86-inch height, a 22.8-square-foot footprint, and a 2,000-pound rating for the complete rack. He says the height suits garages and basements with 8-foot ceilings, which is the space most home gym owners are working with.
- Height: 86 inches.
- Footprint: About 22.8 square feet.
- Smith bar: 33 pounds, the same as the M1.
- Rack capacity: 2,000 pounds total, a number Luke says he will never approach.
- Pulley static load: 352 pounds per side.
- Dip bar static load: 330 pounds, enough for his 210 pounds plus a 100-pound dip belt.
- J hook static load: 330 pounds.
- Pull-up bar: Knurled with wide to neutral grips, which he calls an upgrade over the M1.
Luke says the ratings are credible because RitFit tests its equipment and posts the results. He contrasts that with budget Amazon brands he says advertise 1,000-pound ratings through AI-generated videos, and he says the difference is why he trusts the 2,000-pound figure even though he will never load it.
What Luke Likes About the RitFit M2 3D Pro
Luke's main praise is versatility, and he says the rack handles anything he wants to do and more. He lists the cable system, landmine, Smith machine, and 3D carriage as separate training options that share one frame, with the ability to pin the carriage for vertical-only work.
- Versatility: Cables, landmine, Smith, 3D Smith, and vertical-only Smith work in one rack.
- Stabilizer training: Luke says the 3D path helps him rebuild stability after knee injuries and mimics a barbell squat.
- Storage and layout: The rear attachment beam, three-barbell storage, and removable horns keep the working area clear.
- Pulley feel: Aluminum pulleys with bearings stay smooth under heavy loads.
- Honest ratings: He trusts the published static loads because RitFit tests them.
Luke's summary is that the M2 is a mid-tier rack with a lifetime frame, and that the 3D carriage is the feature that separates it from the M1 2.0. He repeats that the 3D motion is harder, which he sees as proof that it trains stabilizers rather than adding novelty.
His advice for buyers who do not need the 3D path is to look at the RitFit M1 2.0, which he says keeps the vertical Smith and stacks at a lower price. That recommendation comes with the same caveat he applies to the M2: match the machine to the work you actually do.
What Would Luke Change About the M2 3D Pro?
Luke has three fixes he would ask for, and he frames them as feedback rather than reasons to skip the rack. He introduces the list by saying RitFit is a brand that takes notes and works on its products, which is why he bothers to raise them.
His first complaint is the spacing between the Smith hooks, which he says is too wide for a flat bench at his arm length. When he sets up, the bar ends up stuck on his chest instead of racking cleanly, and he suggests more pegs or a rack a couple of inches taller to fit an extra peg between the current ones.
He says Matt from RitFit has already listened to that feedback, which fits the pattern he describes of a brand that revises products. He still wants the change on future versions because arm lengths vary and the whole point of a Smith machine is a safe rack.
The second fix is the lat pulldown cable, which he calls too long even though he gets a decent stretch at 6 feet. He points to Fringe Sport's cable clips as the model: ship one standard cable and let the user clip it to the right length for their body.
The third fix is the bracket that holds the lat pulldown clip, which stops the trolley from reaching its highest position when installed. Luke wants it removable with two strong pins, and until then he stores the clip at the side or hangs it on a hook, an idea he credits to PJ from the Design Build Lift channel.
He is clear that the last issue costs one section of travel at the top, so it is a small annoyance rather than a dealbreaker. The hook spacing matters more to him because it affects how safely he can rack a flat bench press.
How Much Does the RitFit M2 3D Pro Cost?
Luke puts the 3D Smith with stacks close to $3,000 before his code brings it under that mark. RitFit's product page listed the M2 3D Pro with the stack at $2,359.99 as of November 18, 2026, against a regular price of $3,099.99, and whether code RF Luke still works at checkout was not verified for this article.
The same listing showed the M2 3D without the stack at $1,599.99. Luke places the M1 2.0 under $2,000, a figure he gives in the video and one that was not re-verified for this article.
He frames the gap as $800 to $850 and asks whether the 154-pound stacks, the 3D Smith, and the 13-gauge steel justify it. His answer is that the M2 is an upgraded system for buyers who want those three things, while the M1 2.0 remains the lower-cost route to vertical Smith work and cables.
RitFit's Black Friday sales page also listed the M2 3D Pro at $2,359.99 against a $3,099.99 reference price as of November 18, 2026. The same page said M1 and M2 are part of a lowest-price event that may replace tiered discounts, so the cart total is the final check.
Luke still calls the M2 3D Pro a rack that will last the rest of your life, which is his way of saying the price buys a long service life rather than a short-term upgrade.
Conclusion
Luke's verdict is that the RitFit M2 3D Smith Pro is a mid-tier rack built to last, and the 3D carriage is the reason to pay for it. He would point you to the M2 if you want horizontal bar travel, a 154-pound stack per side, and room for attachments, and to the M1 2.0 if the $800 to $850 gap is too wide.
His three fixes are worth knowing before checkout, but none changed his recommendation. Match the machine to the training you do, and treat the 3D feature as the deciding cost.
Disclaimer
This article reports the opinions and observations of one reviewer and is not a substitute for professional instruction. Consult a qualified trainer or physician before starting a new strength program or training around an injury.
References
1. Luke's Garage Gym. RitFit's M2 3D Smith Machine Review | Is This Their Best All-in-One Rack Yet? YouTube. Available at https://www.youtube.com/watch?v=teUzN9r0wag












